1. The reason why the diesel engine cannot start: check the power supply, check the oil supply, consider the possibility of insufficient air intake, consider whether the intake compressive force is insufficient, consider whether the ambient temperature is too low, start the supporting output machinery with load, etc.
2. III: Plug-in open circuit or short circuit. The fuel injector harness, sensor harness, the whole vehicle harness plug-in is not plugged in or the harness is broken or short-circuited. Check the installation of the plug-in and check the connection of the line with a mimeter.
3. Circuit or electronic failure. The phenomenon of this failure is very sudden without any warning. The faults of the circuit include: fuse burnout, high-voltage coil breakage, low-voltage circuit breakage, central ignition wire falling off, split-fire head leakage, spark plug damage. Electronic failure mainly refers to the loss of function of the central computer control panel.
The reason why the diesel generator does not catch fire: 1. The friction surface is not lubricated in time. The lubricating oil film on the cylinder wall is damaged. Corroded by acidic substances. The friction surface is not lubricated in time. During cold start, the oil pump cannot immediately pump the lubricating oil to each friction surface. Make the initial lubrication conditions worse; the lubricating oil film on the cylinder wall is damaged.
The reason why the diesel generator can't catch fire: the friction surface is not lubricated in time. When cold started, it is impossible for the oil pump to immediately send the lubricating oil pressure to each abrasive surface. It makes the lubrication conditions in the initial stage worse; the lubricating oil film of the cylinder wall is destroyed.
The following are the reasons why the diesel generator can't catch fire: The engine oil line is not smooth. It is necessary to check whether the engine oil line is smooth. If you hear a squeaky sound from the fuel injector, it means that the oil line is fine.
Battery failure One of the most common reasons why the generator cannot start is battery failure. This may usually be caused by loose connection or sulfatization (the accumulation of lead sulfate crystals on the electrode plate of a lead-acid battery).
The first type: out of oil.We went out to rescue a car before. The fuel gauge showed that it was below the red line, so naturally it could not catch fire. The second type: the battery is out of power. It may be due to the power loss caused by the headlights not turned off for a long time or the battery life expires. Generally, it is recommended to replace the battery in time in 2 years.
The car battery is damaged. When the car battery is damaged, it is easy for the diesel car to fail to catch fire and naturally fail to start. In response to this situation, you need to go to a professional repair shop in time to deal with it and replace the brand-new battery. The oil transmission system is faulty. There is a blockage in the oil supply pipeline, resulting in the inability to come up the diesel.
Spark plug oil accumulation is a relatively common reason. The car has been starting for too long but has not started. The engine sprays oil to the spark plug. The oil will not burn without ignition. After a long time, it will cause spark plug oil, resulting in unable to ignite.
The main reasons why the diesel engine can't catch fire are as follows: 1. The problem of oil supply. The oil supply time is wrong, too early or too late. The atomization of the nozzle is not good, and the pressure of the oil pump is not enough. The oil line is not smooth, the diesel filter is blocked or there is too little diesel under the filter. There is a problem with the quality of diesel, such as water and oil in diesel.
HS code application in re-export scenarios-APP, download it now, new users will receive a novice gift pack.
1. The reason why the diesel engine cannot start: check the power supply, check the oil supply, consider the possibility of insufficient air intake, consider whether the intake compressive force is insufficient, consider whether the ambient temperature is too low, start the supporting output machinery with load, etc.
2. III: Plug-in open circuit or short circuit. The fuel injector harness, sensor harness, the whole vehicle harness plug-in is not plugged in or the harness is broken or short-circuited. Check the installation of the plug-in and check the connection of the line with a mimeter.
3. Circuit or electronic failure. The phenomenon of this failure is very sudden without any warning. The faults of the circuit include: fuse burnout, high-voltage coil breakage, low-voltage circuit breakage, central ignition wire falling off, split-fire head leakage, spark plug damage. Electronic failure mainly refers to the loss of function of the central computer control panel.
The reason why the diesel generator does not catch fire: 1. The friction surface is not lubricated in time. The lubricating oil film on the cylinder wall is damaged. Corroded by acidic substances. The friction surface is not lubricated in time. During cold start, the oil pump cannot immediately pump the lubricating oil to each friction surface. Make the initial lubrication conditions worse; the lubricating oil film on the cylinder wall is damaged.
The reason why the diesel generator can't catch fire: the friction surface is not lubricated in time. When cold started, it is impossible for the oil pump to immediately send the lubricating oil pressure to each abrasive surface. It makes the lubrication conditions in the initial stage worse; the lubricating oil film of the cylinder wall is destroyed.
The following are the reasons why the diesel generator can't catch fire: The engine oil line is not smooth. It is necessary to check whether the engine oil line is smooth. If you hear a squeaky sound from the fuel injector, it means that the oil line is fine.
Battery failure One of the most common reasons why the generator cannot start is battery failure. This may usually be caused by loose connection or sulfatization (the accumulation of lead sulfate crystals on the electrode plate of a lead-acid battery).
The first type: out of oil.We went out to rescue a car before. The fuel gauge showed that it was below the red line, so naturally it could not catch fire. The second type: the battery is out of power. It may be due to the power loss caused by the headlights not turned off for a long time or the battery life expires. Generally, it is recommended to replace the battery in time in 2 years.
The car battery is damaged. When the car battery is damaged, it is easy for the diesel car to fail to catch fire and naturally fail to start. In response to this situation, you need to go to a professional repair shop in time to deal with it and replace the brand-new battery. The oil transmission system is faulty. There is a blockage in the oil supply pipeline, resulting in the inability to come up the diesel.
Spark plug oil accumulation is a relatively common reason. The car has been starting for too long but has not started. The engine sprays oil to the spark plug. The oil will not burn without ignition. After a long time, it will cause spark plug oil, resulting in unable to ignite.
The main reasons why the diesel engine can't catch fire are as follows: 1. The problem of oil supply. The oil supply time is wrong, too early or too late. The atomization of the nozzle is not good, and the pressure of the oil pump is not enough. The oil line is not smooth, the diesel filter is blocked or there is too little diesel under the filter. There is a problem with the quality of diesel, such as water and oil in diesel.
HS code intelligence for oil and gas industry
author: 2024-12-23 23:08Customs broker performance analysis
author: 2024-12-23 23:00Trade intelligence for luxury goods
author: 2024-12-23 22:16Global trade analytics for decision-makers
author: 2024-12-23 22:04How to adapt to shifting trade policies
author: 2024-12-23 22:02Global trade content syndication
author: 2024-12-23 22:38HS code-driven customs risk scoring
author: 2024-12-23 21:54Processed nuts HS code references
author: 2024-12-23 21:16928.79MB
Check936.66MB
Check593.15MB
Check576.87MB
Check372.28MB
Check725.72MB
Check121.97MB
Check655.63MB
Check223.82MB
Check397.58MB
Check227.84MB
Check394.26MB
Check617.28MB
Check955.49MB
Check689.72MB
Check494.49MB
Check322.27MB
Check643.77MB
Check954.59MB
Check624.76MB
Check163.46MB
Check741.44MB
Check369.76MB
Check638.77MB
Check383.17MB
Check454.42MB
Check454.31MB
Check873.26MB
Check978.69MB
Check125.55MB
Check374.34MB
Check191.38MB
Check185.19MB
Check541.92MB
Check934.16MB
Check925.52MB
CheckScan to install
HS code application in re-export scenarios to discover more
Netizen comments More
2145 Trade data for industrial machinery
2024-12-23 23:11 recommend
1961 Pulp and paper HS code compliance
2024-12-23 22:14 recommend
1691 HS code-driven route-to-market planning
2024-12-23 22:04 recommend
822 Heavy machinery parts HS code verification
2024-12-23 21:51 recommend
989 USA importers database access
2024-12-23 21:04 recommend