1. If the width is too large, there will be no accident during overtaking or if the road marking is narrower than the width of the car, the state stipulates that the car The total width of the vehicle shall not exceed 5m to meet the needs of the use of relevant public roads.
2. However, as long as it meets the national standard "Dimensions, Axle Weight and Mass Limits of Road Vehicles" (GB1589-2004), they are all standard sizes.Measurement method of car size: length and number of times; width × height. As the name implies, the so-called length, width and height are the external dimensions of the car, usually in millimeters (mm).
3. Width is the distance between the most prominent points of the outer sheet metal of the body. The length data of a car is the distance from the front of the front to the end of the rear of the car. The width is the distance between the most prominent points of the outer sheet metal of the car body. Generally, the front wheel eyebrow position of the car is the widest, and the general reflector is not included in the width of the body.
4. According to the common rules in the industry, the width of the body does not include the width of the left and right rearview mirrors, that is, the width after the rearview mirror is folded. The height of the car body is defined as: the distance from the ground to the highest point of the car. The so-called highest point is the highest position on the top of the body, but does not include the length of the roof antenna.
5. Vehicle width: Vehicle width is the distance between the two planes parallel to the longitudinal symmetrical plane of the vehicle and facing the fixed protruding parts on both sides of the vehicle. The automatic measuring instrument of vehicle outline size should comply with the measurement regulations, and the maximum allowable error of the measuring instrument: 1% or 20mm.
6. The body size is the data of the length, width and height of the car, indicating the external size of the car body. Body length × width × height measurement standard: body length refers to the distance from the most prominent position at the front of the car to the most prominent position at the rear of the car.
Benchmarks In actual measurement work, the plane of the body corrector is generally taken as the height reference plane.
In the body knotIn structural maintenance, when measuring the body structure data with the body measurement system, there are three important dimensional reference benchmarks: reference surface, central surface and zero plane.
Therefore, the use of steel tape measure and gauge can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and production year should be correctly selected. Parameter comparison When selecting the measurement reference point, the following principles should usually be followed. 1 Confirm that the measurement reference point is not deformed.
The body width is defined as the distance between the two extreme points in the direction of the width of the car, that is, the distance between the most prominent positions on the left and right of the car body. According to the general rules of the industry, the body width does not include the extension width of the left and right rearview mirrors, that is, the width of the folding rearview mirrors. The body height is defined as the distance from the ground to the highest point of the car.
The quality of the whole vehicle equipment (kg): the quality of the car is fully equipped, including the quality of all equipment such as lubricating oil, fuel, accompanying tools, spare tires, etc. Maximum total mass (kg): the total mass when the car is fully loaded. Maximum loading mass (kg): the maximum loading mass when the car is driving on the road.
Therefore, the use of steel tape measure and gauge ruler can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and year of production should be correctly selected. ( 2) Parameter comparison: When comparing parameters, the following principles should generally be followed: ensure that the measurement reference point is not deformed.
1. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
2. You need a tape measure or laser rangefinder. If you choose to use a tape measure, make sure it is accurate and long enough to measure the length of the entire body. If you choose to use a laser rangefinder, follow the instructions to make sure that it has been calibrated and ready for use.
3. In order to accurately obtain the body data, the three steps are the measurement of the size, the measurement of the upper body size, and the measurement of the front size of the body. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. Measurement of the overall deformation of the car body: Body shaping positioning detection is to use the measurement system provided by the straightening system to measure the coordinate parameters of each measurement point on the body, and compare the measurement data with the standard data of the model to check the straightening quality.
5. Stop the car after driving 10km on the road with poor road conditions, and touch the shock absorber shell with your hand. If it is not hot enough, it means that there is no resistance inside the shock absorber and the shock absorber does not work.
The front bundle ruler can be used to check and measure the front bundle. The tested vehicle must ensure that the tire pressure, the wheel is not in the center, the steering mechanism and the wheel bearing adjustment are in good condition, and the front wheel must be in the center and straight. When measuring with a front ruler, park the car on a flat, dry and clean ground.
Measurement method of automobile front bundle: First of all, the measurement method of automobile wheel bearing clearance is adjusted, and the tire inflation pressure conforms to the regulations.
The adjustment and measurement of the front beam of the car are as follows: the front beam of the front wheel is to make the distance between the front end of the two front wheels of the car smaller than the distance of the rear end.The difference in distance is called the front beam value. Looking down from the top of the car, the left and right front wheels form an "eight" shape with an opening to the back; the front bundle of the front wheel can be adjusted by changing the length of the crossbar.
Checking the front bundle value is generally carried out on a special front wheel locator. The front beam measurement method is first of all to adjust the gap of the automobile wheel hub bearing, and the tire inflation pressure conforms to the regulations. Park the car on the horizontal road and drive in a straight line.
Therefore, when the current bundle value is inappropriate, it needs to be adjusted and measured. To measure the front beam of a car, it is generally necessary to use a special front wheel locator, and generally there is no such professional instrument for self-measurement, and it can only be measured through simple tools. Of course, there is a certain error in the front beam of the car measured in this way.
1. Car size detection is as follows: the body length is defined as the distance between the two extreme points of the car, that is, the distance between the two points from the most prominent position of the front bumper of the car to the most prominent position of the rear bumper.
2. Body size: First, we will measure the size of each part of the car body, including the length, width and height. These data are crucial to the design, manufacture and safety of vehicles. For example, if the body width exceeds the specified limit, the vehicle may not be able to drive on certain roads.
3. Measurement of size: In the body structure, most of the control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. When the freight vehicle passes through the off-site law enforcement monitoring point normally at a running speed range of 0.5-100km/h, the Shenbang outline size measurement ADM system can automatically complete the identification and measurement of the length, width and height profile size and wheelbase of the freight vehicle, and output the correct measurement results to Off-site law enforcement edge management server.
Pharmaceutical raw materials HS code checks-APP, download it now, new users will receive a novice gift pack.
1. If the width is too large, there will be no accident during overtaking or if the road marking is narrower than the width of the car, the state stipulates that the car The total width of the vehicle shall not exceed 5m to meet the needs of the use of relevant public roads.
2. However, as long as it meets the national standard "Dimensions, Axle Weight and Mass Limits of Road Vehicles" (GB1589-2004), they are all standard sizes.Measurement method of car size: length and number of times; width × height. As the name implies, the so-called length, width and height are the external dimensions of the car, usually in millimeters (mm).
3. Width is the distance between the most prominent points of the outer sheet metal of the body. The length data of a car is the distance from the front of the front to the end of the rear of the car. The width is the distance between the most prominent points of the outer sheet metal of the car body. Generally, the front wheel eyebrow position of the car is the widest, and the general reflector is not included in the width of the body.
4. According to the common rules in the industry, the width of the body does not include the width of the left and right rearview mirrors, that is, the width after the rearview mirror is folded. The height of the car body is defined as: the distance from the ground to the highest point of the car. The so-called highest point is the highest position on the top of the body, but does not include the length of the roof antenna.
5. Vehicle width: Vehicle width is the distance between the two planes parallel to the longitudinal symmetrical plane of the vehicle and facing the fixed protruding parts on both sides of the vehicle. The automatic measuring instrument of vehicle outline size should comply with the measurement regulations, and the maximum allowable error of the measuring instrument: 1% or 20mm.
6. The body size is the data of the length, width and height of the car, indicating the external size of the car body. Body length × width × height measurement standard: body length refers to the distance from the most prominent position at the front of the car to the most prominent position at the rear of the car.
Benchmarks In actual measurement work, the plane of the body corrector is generally taken as the height reference plane.
In the body knotIn structural maintenance, when measuring the body structure data with the body measurement system, there are three important dimensional reference benchmarks: reference surface, central surface and zero plane.
Therefore, the use of steel tape measure and gauge can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and production year should be correctly selected. Parameter comparison When selecting the measurement reference point, the following principles should usually be followed. 1 Confirm that the measurement reference point is not deformed.
The body width is defined as the distance between the two extreme points in the direction of the width of the car, that is, the distance between the most prominent positions on the left and right of the car body. According to the general rules of the industry, the body width does not include the extension width of the left and right rearview mirrors, that is, the width of the folding rearview mirrors. The body height is defined as the distance from the ground to the highest point of the car.
The quality of the whole vehicle equipment (kg): the quality of the car is fully equipped, including the quality of all equipment such as lubricating oil, fuel, accompanying tools, spare tires, etc. Maximum total mass (kg): the total mass when the car is fully loaded. Maximum loading mass (kg): the maximum loading mass when the car is driving on the road.
Therefore, the use of steel tape measure and gauge ruler can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and year of production should be correctly selected. ( 2) Parameter comparison: When comparing parameters, the following principles should generally be followed: ensure that the measurement reference point is not deformed.
1. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
2. You need a tape measure or laser rangefinder. If you choose to use a tape measure, make sure it is accurate and long enough to measure the length of the entire body. If you choose to use a laser rangefinder, follow the instructions to make sure that it has been calibrated and ready for use.
3. In order to accurately obtain the body data, the three steps are the measurement of the size, the measurement of the upper body size, and the measurement of the front size of the body. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. Measurement of the overall deformation of the car body: Body shaping positioning detection is to use the measurement system provided by the straightening system to measure the coordinate parameters of each measurement point on the body, and compare the measurement data with the standard data of the model to check the straightening quality.
5. Stop the car after driving 10km on the road with poor road conditions, and touch the shock absorber shell with your hand. If it is not hot enough, it means that there is no resistance inside the shock absorber and the shock absorber does not work.
The front bundle ruler can be used to check and measure the front bundle. The tested vehicle must ensure that the tire pressure, the wheel is not in the center, the steering mechanism and the wheel bearing adjustment are in good condition, and the front wheel must be in the center and straight. When measuring with a front ruler, park the car on a flat, dry and clean ground.
Measurement method of automobile front bundle: First of all, the measurement method of automobile wheel bearing clearance is adjusted, and the tire inflation pressure conforms to the regulations.
The adjustment and measurement of the front beam of the car are as follows: the front beam of the front wheel is to make the distance between the front end of the two front wheels of the car smaller than the distance of the rear end.The difference in distance is called the front beam value. Looking down from the top of the car, the left and right front wheels form an "eight" shape with an opening to the back; the front bundle of the front wheel can be adjusted by changing the length of the crossbar.
Checking the front bundle value is generally carried out on a special front wheel locator. The front beam measurement method is first of all to adjust the gap of the automobile wheel hub bearing, and the tire inflation pressure conforms to the regulations. Park the car on the horizontal road and drive in a straight line.
Therefore, when the current bundle value is inappropriate, it needs to be adjusted and measured. To measure the front beam of a car, it is generally necessary to use a special front wheel locator, and generally there is no such professional instrument for self-measurement, and it can only be measured through simple tools. Of course, there is a certain error in the front beam of the car measured in this way.
1. Car size detection is as follows: the body length is defined as the distance between the two extreme points of the car, that is, the distance between the two points from the most prominent position of the front bumper of the car to the most prominent position of the rear bumper.
2. Body size: First, we will measure the size of each part of the car body, including the length, width and height. These data are crucial to the design, manufacture and safety of vehicles. For example, if the body width exceeds the specified limit, the vehicle may not be able to drive on certain roads.
3. Measurement of size: In the body structure, most of the control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. When the freight vehicle passes through the off-site law enforcement monitoring point normally at a running speed range of 0.5-100km/h, the Shenbang outline size measurement ADM system can automatically complete the identification and measurement of the length, width and height profile size and wheelbase of the freight vehicle, and output the correct measurement results to Off-site law enforcement edge management server.
Industry consolidation via HS code data
author: 2024-12-24 01:27HS code-driven customs risk scoring
author: 2024-12-24 01:02Real-time container throughput data
author: 2024-12-23 23:08Data-driven supply chain partnerships
author: 2024-12-24 01:42Global trade data storytelling
author: 2024-12-24 01:35HS code verification for exporters
author: 2024-12-24 01:06HS code monitoring in European supply chains
author: 2024-12-24 00:14Mining equipment HS code references
author: 2024-12-24 00:01
HS code-driven sectoral analysis
369.98MB
Check
HS code-based green supply chain metrics
659.45MB
Check
Country-specific HS code exemptions
789.37MB
Check
How to handle multi-currency billing
897.35MB
Check
How to find authorized economic operators
627.22MB
Check
How to find emerging export markets
342.36MB
Check
Russia HS code-based trade compliance
585.31MB
Check
HS code utilization for tariff refunds
452.25MB
Check
International trade knowledge base
918.24MB
Check
HS code alignment with labeling standards
619.53MB
Check
HS code-based supply risk mitigation
342.77MB
Check
Global trade resource libraries
785.99MB
Check
How to forecast trade demand spikes
166.48MB
Check
Customs procedure optimization
683.94MB
Check
Comparative HS code duty analysis
327.21MB
Check
Exporter data
726.46MB
Check
Integrated circuits HS code verification
535.83MB
Check
Segmenting data by HS code and region
847.46MB
Check
global trade management
466.28MB
Check
Plastics raw materials HS code lookups
421.47MB
Check
Global trade intelligence for investors
356.89MB
Check
Electronics global trade by HS code
512.38MB
Check
HS code alignment with logistics software
574.37MB
Check
Grain imports HS code data trends
366.19MB
Check
Inland freight HS code applicability
886.14MB
Check
HS code compliance for African Union members
817.48MB
Check
HS code-based multi-country consolidation
567.95MB
Check
Segmenting data by HS code and region
531.14MB
Check
HS code-based compliance in bilateral trades
371.57MB
Check
HS code alignment with sustainability targets
349.51MB
Check
Refined metals HS code references
511.82MB
Check
Real-time customs data reports
589.34MB
Check
WTO trade compliance resources
958.99MB
Check
Trade finance data solutions
496.11MB
Check
Biodegradable materials HS code verification
137.74MB
Check
Machinery exports HS code insights
192.95MB
Check
Scan to install
Pharmaceutical raw materials HS code checks to discover more
Netizen comments More
2502 Trade data for intellectual property checks
2024-12-24 01:40 recommend
1659 Global trade data for currency hedging
2024-12-24 01:21 recommend
932 Global trade analysis dashboard
2024-12-24 00:27 recommend
2433 Leather goods HS code classification
2024-12-24 00:22 recommend
1814 Non-tariff barriers by HS code
2024-12-23 23:07 recommend