Pharma R&D materials HS code verification

List of contents of this article:

• 1,Pharma R&D materials HS code verification How to light a car?
• 2, What should I do if the car is on fire but it can't start?
• 3, 4, How to ignit a car

How to light a car?

1,Insert the key in the Lock position without twisting it, wait for about 2 seconds, and then twist the key directly through the ACC position to stop at the ON position and wait for about 5 seconds.

2. There are two types of car ignition, one is one-button start key, and the other is mechanical start key. If it is a mechanical start key, it must be inserted into the corresponding keyhole. Then check the vehicle to see if the handbrake is in the correct position, tighten or brake. Turn on the power supply, let the vehicle self-check, and check whether the gear is in P gear.

3. [Pacific Automobile Network] For automatic transmission models, models equipped with one-button start function, first press the start button without stepping on the brake. At this time, the vehicle is energized, and the driving computer begins to self-check. After the self-inspection is completed, hang the gear into N gear, step on the brake, and press the start again. Press the button to ignite, and the ignition is completed.

4. Before starting, you should turn on the ignition switch and wait for about 5 seconds to let the oil pump work before starting. It is best to turn on the lights, radios and other electrical equipment after starting the engine. Before parking, turn off these electrical appliances that consume electricity and then turn off the engine. 2 Some drivers, in winter The season starts the car and doesn't work.

5. Before starting, make sure that the gear of the car is in idle gear, then step on the clutch, first unstwew the key to the ACC gear, stay for about 3 to 5 seconds, let the car circuit carry out the system self-check, and then stwear it to START gear for startup after it is normal. After the startup is completed, you must release the key and let the key return to the ON gear.

The car is on fireBut what if it can't be started

1. When the car starts, just hang the gear to the P gear; if the car battery is sufficiently charged, the car can catch fire; unlock the steering wheel, and if the steering wheel is not unlocked, it will not start and there will be a rattling sound. Analysis of the specific reasons why the car can't catch fire: oil problem.

2. The starting motor failed and the flywheel could not be rotated. When starting the vehicle, check whether the starting motor is working. The battery failed and could not store the power. If you can only hear the sound of the starter when starting the car, it is likely that it cannot be started due to the battery power failure.

3. The repair method of the car that does not catch fire: the first situation: If there is no problem at the beginning, the later start-up time will beThe longer it takes, until one day it suddenly doesn't start, it should be a problem with the ignition system or fuel supply system of the engine. In this case, you need to find a professional car repairman to repair it.

4. The car is lit but can't start. It is necessary to check whether the fuel pump of the car is damaged. Usually, the fuel pump will affect the ignition of the car. You can check and replace the fuel pump directly at a professional repair shop.

5. The reason why the car can't start is likely to be that the battery is out of power, resulting in insufficient power to drive the engine, resulting in the inability to start the engine. Therefore, the solutions are: use the prepared starting power supply to start; find another car to start; call your insurance company for help.

6. JingleThe fire cannot be started due to the following reasons: the voltage of the car battery is too low or fails, and improper daily use will lead to the loss of battery power. Generally, the battery life is 3 to 5 years. If this period is exceeded, it needs to be replaced in time. The fuel system is insufficiently supplied and cannot meet the mixed gas-air-fuel ratio required by the engine.

How to ignite the car

1. Check whether the power of the battery meets the requirements. If the power is too low, it cannot be ignited normally. At this time, you need to use the battery charger to charge it. After the power meets the normal requirements, it can be ignited.

2. Do not twist the inserted key in the Lock position and wait for about 2 seconds. After that, you can directly stop at the ON position through the ACC position and wait for about 5 seconds.

3. However, for temporary or short-term parking, you don't need to pause. Just observe the yellow signal light on the dashboard to turn off, and then you can start quickly. When starting a fire with a key, please remember the following: do not turn the key to the start position after starting a fire, and do not use the processed key.

4. The correct way to ignit the car is as follows: insertWhen the ignition key and the "start" vehicle starts, the instrument indicator light will light up briefly and then turn off, and the new car computer will enter the self-check state (about 6 seconds). If the fault light is still on after the end, you need to turn off the engine and troubleshoot before restarting the engine.

5. [Pacific Automobile Network] For automatic transmission models, models equipped with one-button start function, first press the start button without stepping on the brake. At this time, the vehicle is energized, and the driving computer begins to self-check. After the self-inspection is completed, hang the gear into the N gear, step on the brake, and press the start again. Press the button to ignite, and the ignition is completed.

6. Before starting, make sure that the gear of the car is in idle gear, then step on the clutch, first turn the key to the ACC gear, stay for about 3 to 5 seconds, let the car circuit carry out the system self-check, and then turn it to START gear for startup after normal.After the startup is completed, you must release the key and let the key return to the ON gear.

How to ignite the car

1. Insert the key in the Lock position without twisting it, wait for about 2 seconds, and then you can directly stop at the ON position through the ACC position and wait for about 5 seconds.

2. Check whether the power of the battery meets the requirements. If the power is too low, it cannot be ignited normally. At this time, you need to use the battery charger to charge, and wait for the battery to meet the normal requirements before it can be ignited.

3. The steps for car ignition are: step on the clutch and wait for 5 to 8 seconds when turning the ignition key to the ON position; then turn the key to the starting position to start the engine; release the ignition key immediately after the engine starts smoothly and let it automatically return to the ON position.

4. When the car is igniting, you should step on the clutch and step on the brake. Stepping on the clutch can reduce the load of the engine, which is very important, because the clutch is the switch that cuts off the engine and gearbox. If you don't step on the clutch at this time, you will largely avoid the situation of stepping on the accelerator when you are on the engine. If it is idle Then step on the clutch when you are on fire.