1. You have solved this problem and there are still some problems, that is, the driver. For example, the graphics card and sound card drivers are easy to have problems. If they can't be installed or have problems, Microsoft has stopped developing the corresponding drivers for the XP system. It only depends on whether you are lucky or not.
2. The maintenance department has told you that the XP system cannot be installed, indicating that the motherboard chip is HM86 level and supports the fourth-generation CPU Haswell processor.
3. After power-on, press DEL to enter BIOS, LOAD DEFAULTS SETTINGS, restore the default settings, save and restart 2.
4. Your notebook has not been tested for the XP system before leaving the factory. It is recommended that you do not install the XP system. IT IS RECOMMENDED THAT YOU USE WIN7 OR WIN8 SYSTEM TO GET THE BEST PERFORMANCE AND STABILITY.
5. This is a little complicated. So to speak, the current hard disks are all SATA interfaces, while in the XP system era, the hard disk interfaces are all IDE. That is to say, XP does not recognize the hard disk with SATA interface.
The way to install the XP system on HP notebooks is to disable the SATA local mode to start the laptop. Press the F10 key (or the key specified by the laptop) repeatedly until the laptop enters the Computer Setup interface. Use the arrow keys to select System Configuration.
Change the boot order according to how the computer enters the bios, start the USB disk, and then enter the win8pe system. Select the winxp system gho version in the installation tool, and select the c disk as the system disk. The program will perform the restore operation and click OK.
Now most of the newly released machines use sata hard disks, because the xp system is not integrated with sTherefore, the ata driver needs to be loaded before installing the sata driver to install the xp system normally. However, because it is more troublesome to install the sata driver, it is better not to install the xp system if you do not have to use the xp system.
Your computer has not been officially tested for the XP system when it left the factory. The official cannot guarantee that the machine will be used normally after installing the XP system. It is officially recommended that you use the tested Win7 system.
1. Turn on the computer, start the USB flash drive, and select the win8pe system to enter. Select the gho version of the winxp system and use the c disk as the system disk. Pop-up window, click "OK". Then restart the computer and wait for the computer to release the gho image to complete. Then restart the computer and pop up the installation process of the computer program.
2. Unzip the SATA driver and copy the program in the decompressed folder to the root directory of the floppy disk. ( 2) Put it into the operating system CD-ROM and connectOkay, USB floppy drive, restart the machine, press F9 to enter the boot menu option, use the direction key to select the optical drive, and press Enter to start.
3. If your machine is pre-installed with the Microsoft Windows operating system when you buy it and your machine's operating system is still pre-installed, it is recommended that you try to save important files and restart the machine. When the HP logo appears on the machine, click F11 to restore it with one click. Check the system of the machine to see if it can solve the problem you encountered.
4. How to install the XP system. The first step is to set the light start: the so-called light start means that the computer first reads the optical drive when starting up. In this way, if there is a CD with an optical start function in the optical drive, it can be read out before the hard disk starts (for example, when installing the system from the CD-ROM).
5. The first one: HP's new machine is a graphical version of BIOS, which can be operated with the mouse. Press F10 to enter bios when booting up. In System Configuration---SATA Device Mode, you can select AHCI or IDE here. You can click it with the mouse to select IDE, and then press the "X" button in the lower left corner and select Y. ES.
Change the startup order according to how the computer enters bios, start the USB disk, and then enter the win8pe system, and select the winxp system in the installation tool. Unify the gho version, and select the c disk as the system disk. The program will perform the restore operation, click OK.
The way to install the XP system on HP notebooks is to disable the SATA local mode to start the laptop. Press the F10 key (or the key specified by the laptop) repeatedly until the laptop enters the Computer Setup interface. Use the arrow keys to select System Configuration.
You need to confirm whether these two CDs are XP system CDs. If not, you can look for XP system CDs again.
Drilling equipment HS code mapping-APP, download it now, new users will receive a novice gift pack.
1. You have solved this problem and there are still some problems, that is, the driver. For example, the graphics card and sound card drivers are easy to have problems. If they can't be installed or have problems, Microsoft has stopped developing the corresponding drivers for the XP system. It only depends on whether you are lucky or not.
2. The maintenance department has told you that the XP system cannot be installed, indicating that the motherboard chip is HM86 level and supports the fourth-generation CPU Haswell processor.
3. After power-on, press DEL to enter BIOS, LOAD DEFAULTS SETTINGS, restore the default settings, save and restart 2.
4. Your notebook has not been tested for the XP system before leaving the factory. It is recommended that you do not install the XP system. IT IS RECOMMENDED THAT YOU USE WIN7 OR WIN8 SYSTEM TO GET THE BEST PERFORMANCE AND STABILITY.
5. This is a little complicated. So to speak, the current hard disks are all SATA interfaces, while in the XP system era, the hard disk interfaces are all IDE. That is to say, XP does not recognize the hard disk with SATA interface.
The way to install the XP system on HP notebooks is to disable the SATA local mode to start the laptop. Press the F10 key (or the key specified by the laptop) repeatedly until the laptop enters the Computer Setup interface. Use the arrow keys to select System Configuration.
Change the boot order according to how the computer enters the bios, start the USB disk, and then enter the win8pe system. Select the winxp system gho version in the installation tool, and select the c disk as the system disk. The program will perform the restore operation and click OK.
Now most of the newly released machines use sata hard disks, because the xp system is not integrated with sTherefore, the ata driver needs to be loaded before installing the sata driver to install the xp system normally. However, because it is more troublesome to install the sata driver, it is better not to install the xp system if you do not have to use the xp system.
Your computer has not been officially tested for the XP system when it left the factory. The official cannot guarantee that the machine will be used normally after installing the XP system. It is officially recommended that you use the tested Win7 system.
1. Turn on the computer, start the USB flash drive, and select the win8pe system to enter. Select the gho version of the winxp system and use the c disk as the system disk. Pop-up window, click "OK". Then restart the computer and wait for the computer to release the gho image to complete. Then restart the computer and pop up the installation process of the computer program.
2. Unzip the SATA driver and copy the program in the decompressed folder to the root directory of the floppy disk. ( 2) Put it into the operating system CD-ROM and connectOkay, USB floppy drive, restart the machine, press F9 to enter the boot menu option, use the direction key to select the optical drive, and press Enter to start.
3. If your machine is pre-installed with the Microsoft Windows operating system when you buy it and your machine's operating system is still pre-installed, it is recommended that you try to save important files and restart the machine. When the HP logo appears on the machine, click F11 to restore it with one click. Check the system of the machine to see if it can solve the problem you encountered.
4. How to install the XP system. The first step is to set the light start: the so-called light start means that the computer first reads the optical drive when starting up. In this way, if there is a CD with an optical start function in the optical drive, it can be read out before the hard disk starts (for example, when installing the system from the CD-ROM).
5. The first one: HP's new machine is a graphical version of BIOS, which can be operated with the mouse. Press F10 to enter bios when booting up. In System Configuration---SATA Device Mode, you can select AHCI or IDE here. You can click it with the mouse to select IDE, and then press the "X" button in the lower left corner and select Y. ES.
Change the startup order according to how the computer enters bios, start the USB disk, and then enter the win8pe system, and select the winxp system in the installation tool. Unify the gho version, and select the c disk as the system disk. The program will perform the restore operation, click OK.
The way to install the XP system on HP notebooks is to disable the SATA local mode to start the laptop. Press the F10 key (or the key specified by the laptop) repeatedly until the laptop enters the Computer Setup interface. Use the arrow keys to select System Configuration.
You need to confirm whether these two CDs are XP system CDs. If not, you can look for XP system CDs again.
HS code-based trade data analytics
author: 2024-12-23 22:21How to access historical shipment records
author: 2024-12-23 21:33How to forecast seasonal import demands
author: 2024-12-23 21:18Ship parts HS code verification
author: 2024-12-23 20:26HS code harmonization in NAFTA region
author: 2024-12-23 22:45Global trade data warehousing solutions
author: 2024-12-23 21:57Comparing international shipping carriers
author: 2024-12-23 21:20Data-driven multimodal transport decisions
author: 2024-12-23 20:35Predictive trade route realignment
author: 2024-12-23 20:19625.12MB
Check825.75MB
Check158.82MB
Check695.21MB
Check769.28MB
Check942.77MB
Check917.81MB
Check495.81MB
Check342.78MB
Check991.26MB
Check494.75MB
Check756.31MB
Check572.18MB
Check321.26MB
Check455.34MB
Check337.93MB
Check569.43MB
Check982.68MB
Check924.13MB
Check229.93MB
Check636.75MB
Check491.43MB
Check723.36MB
Check343.77MB
Check552.55MB
Check812.96MB
Check699.95MB
Check789.12MB
Check587.46MB
Check221.82MB
Check853.87MB
Check168.98MB
Check329.13MB
Check637.98MB
Check393.95MB
Check871.73MB
CheckScan to install
Drilling equipment HS code mapping to discover more
Netizen comments More
2145 Predictive trade infrastructure analysis
2024-12-23 22:59 recommend
884 How to benchmark HS code usage
2024-12-23 22:46 recommend
1173 Global trade intelligence forums
2024-12-23 21:59 recommend
2331 Trade data for pharmaceutical imports
2024-12-23 21:31 recommend
456 Optimizing FTAs with HS code data
2024-12-23 21:11 recommend