Trade data-driven logistics planning

List of the contents of this article:

• 1,Trade data-driven logistics planning What is the reason for the oil leakage of the fifteen-horsepower large wheel of Yuchai engine diesel
• 2, Will disassembling the big wheel of the Fox engine affect the timing
• 3, Is the big turbine big?
• 4, The difference between large turbines and small turbines; Is the hysteresis of large turbines large< /Li>
• 5, 195 What's the use of installing large wheels in diesel engines?

What is the reason for the oil leakage of the fifteen-horse large wheel of Yuchai engine diesel

Because the amount of oil in the gearbox is certain. It won't take long for you to leak like this. The lighter bearing is damaged and the gear is worn. The heavy gearbox will be scrapped. It is recommended that you repair the leaking part as soon as possible. What if only the sealant leaks as you said? The cost of changing the gasket is very low.

Hello! You must have oil in your combustion room, so you need to check the oil level of the oil. Burning oil or dripping oil is generally caused by poor sealing or wear, which will burn the engine.

The oil leakage or large amount of oil dripping of the vehicle engine respirator (lower exhaust) is mainly caused by the loose sealing of the valve or the serious wear of the four supporting equipment.

Will the disassembly of the large wheel of the Fox engine affect the timing

Will the timing of the crankshaft be chaotic when the Fox is stuck and the belt pulley is stuck? Expand I'll answer and share WeChat scan busy. Please try again later. Sina Weibo QQ Space Report Browse 6 times You can choose one or more of the following keywords to search for relevant information. You can also directly click "Search Information" to search for the whole question.

The classic Ford Focus can be timed without removing the timing chain. It can't be done without disassembly. It must be disassembled before the tensioner can be locked and aimed at the point on the chain. When replacing the timing chain, there is no need to disassemble the engine, just open the chain cover on the engine.

In order to adjust the timing, the engine must be lowered and a part of it must be dismantled.To make the intake valve and exhaust valve of the camshaft completely closed in an inverted eight-shape, the crankshaft must be turned to the upper stop point. Use special tools to fix the groove behind the camshaft. After fixing, put the special tool parallel to the cylinder head and remove a bolt from the cylinder block close to the semi-axis.

Remantle a bolt from the cylinder block near the semi-axis. Lock the camshaft fixing bolt, tighten the crankshaft pulley bolt as required, align it according to the timing mark, and finally try it out. The FocusDuratec-He inverted aluminum alloy engine is made of all-aluminum alloy and adopts an inverted design.

Is the big turbine lag big

1. The bigger the turbine, the greater the lag. It takes a certain amount of time for the turbocharged pressure to rise to a certain value. The greater the turbine hysteresis, the higher the engine speed and the lower the engine speed.

2. The greater the turbine delay. It takes a certain amount of time for the turbocharged pressure to rise to a certain value. The greater the turbine lag, the higher the engine speed, and the smaller the engine speed. The turbine lag is affected by the turbine size, engine displacement, engine modification degree, turbine shaft rotational inertia, turbine effect, intake loss, exhaust back pressure and other factors.

3. If the turbine lag is serious, it will inevitably affect the driving experience. The specific manifestation is that if you step on the accelerator lightly, you will not go, but if you step on the accelerator, you will run the car. The moment you just step on the accelerator, there is not much power output, and it is even weaker than some naturally aspirated engines. You need to wait for the speed to reach a certain speed before the power to stand out.

4. Take a 0T model as an example. If the turbo is too slow, it will weaken its power performance when crawling at low speed, and may even be worse than the 0L naturally aspirated model.

The difference between large turbine and small turbine; Is the big turbine hysteresis big

1. Large turbine and small The difference between turbines is key to two aspects: one is that the time of intervention is different, and the other is that the power of supply is different. The small turbine intervened earlier, and may intervene at around 1500 rvel, but the power supply is limited.

2. The larger the turbine, the greater the lag. It takes a certain amount of time for the turbocharged pressure to rise to a certain value. The greater the turbine hysteresis, the higher the engine speed and the lower the engine speed.

3. The greater the turbine delay. It takes a certain amount of time for the turbocharged pressure to rise to a certain value. The greater the turbine lag, the higher the engine speed, and the smaller the engine speed. The turbine lag is affected by the turbine size, engine displacement, engine modification degree, turbine shaft rotational inertia, turbine effect, intake loss, exhaust back pressure and other factors.

4. [Pacific Automobile Network] The big turbine is slow. There are many factors that cause turbine hysteresis, including the size of the turbine, engine displacement, the degree of engine modification, the rotational inertia of the turbine shaft, the efficiency of the turbine, the intake loss, the exhaust back pressure, etc.Under normal circumstances, the engine displacement remains unchanged, and the larger the turbine, the greater the turbine delay.

5. Small inertia turbine: The turbine relies on the exhaust gas generated by the engine to drive the turbine blade to rotate at high speed, and then compress the air that is about to enter the engine to improve the efficiency of the work and increase the power. In the past, it was a large turbine, and the turbine blade was relatively large, so there was more exhaust gas that needed to push the fan blade to rotate, so the turbine lag time was longer.

195 What's the use of installing large wheels in diesel engines?

1. The diesel engine flywheel is an energy storage device. The single-cylinder diesel engine has only one work stroke as the working stroke, and the other three strokes are auxiliary strokes. These three journeys can only be completed by relying on the inertia of the flywheel operation.

2. In addition, there are many diesel cars in Europe. Due to the large vibration of the diesel engine, the use of dual-mass flywheels can effectively reduce the vibration of the engine.

3. The pulley is a transmission component in a transmission mechanism. Any transmission component involves the size of the power, the size of the force, the size of the force pitch, and the size of the speed ratio. Therefore, it is generally best to use the original factory. If you change it by yourself, you can do a simple calculation before implementing it.