CIS countries HS code usage patterns

List of the table of contents of this article:

• 1,CIS countries HS code usage patterns Why can't my computer install half of the system
• 2, What should I do if the system is installed halfway through the system is installed and the blue screen is turned on?
• 3, What's the problem with the blue screen halfway through the installation of the system??

IWhy can't the computer install half of the system?

1. It may also be a hard disk problem. ( 1) Hang this disk to another computer as a scander disk, and scan and repair the C disk.

2. If the GHOST system file is damaged, just download a system file again. The bad channel of the computer hard disk can be solved by restoring its bad channel. The specific method is as follows: first, find the bad channel disk we need to repair, such as: C disk, D disk, E disk, F disk, etc., and then right-click and select "Properties"; for details, please refer to the figure below.

3. If there is no problem, it may be that the data cable of the hard disk is of poor quality or the contact is not good, which may lead to it. Pay attention to replace the hard disk data cable and plug it into the motherboard first, or change the two ends of the cable.If it still doesn't work, change the root line to test.

What should I do if the system is installed halfway and the system is installed and the blue screen is turned on?

"system restore" appears In the speech box, and select "Restore my computer to an earlier time". In this way, you can use the system restore function of the Windows system to restore to the restore point that could be started normally before.(If any) Use the system installation CD, put it into the optical drive, restart the computer, and enter the CD-ROM installation system state.

USB disk compatibility problem. At present, there are many fake USB disks on the Internet. The poor compatibility of these USB disks will cause the loading of the USB disk to be slow to start the pe, and sometimes even dead. At this time, it is necessary to replace a USB disk with good compatibility performance to make it into a u boot disk.

If you encounter this problem, exit PE first, restart the computer and enter the BIOS interface to modify the boot mode, change the UEFI boot mode to Legacy mode, and then re-enter PE to continue the installation. The solution is as follows: exit the PE system, restart the computer, and enter the BIOS when it is turned on.

What's the problem with the blue screen halfway through the installation of the system??

If the computer has a blue screen when using an application software, the blue screen failure may be caused by this program software. Generally, the program software can be uninstalled and reinstalled to troubleshoot; if not, it may be that the program software itself has an error and cannot be used. 2.

Install the blue screen of the system. If it is not a problem with the hard disk mode, it may be a memory problem. The following is a personal summary of Baidu Knows Ctangel. It is not a network copy. It is all encountered in personal daily work and the cause is clearly determined. If you need to copy, please indicate the source. Here are several typical causes and solutions of blue screen failure.

. Blue screen failure caused by the exhaustion of system resources. Example: BlueScreen failures often occur when doing a relatively large task, or when saving and copying, and often occur suddenly. The cause of this kind of failure is mainly related to the occupation of three heap resources (system resources, user resources, GDI resources).

The solution to the blue screen of the computer installation system is as follows: restart once first, and the restart interface is shown in the figure. If the above methods can't solve the problem, it is possible that the computer has been infected with a virus. Just download the anti-virus software to anti-virus. If the computer is infected with a stubborn virus, you can reinstall the system, as shown in the figure.

There are two reasons for the blue screen when reinstalling the system: your C disk is an inactive partition. You just need to set the C disk as an active partition, and the reason will not be explained. The meaning of the surface text will be explained. Another may be the reason for your SATA hard disk driver.

I) It should be that the partition was not formatted when reinstalling xp, which conflicts with the original system file, resulting in a blue screen. It is recommended that you use the USB disk pe system, format the partition first, and then install xp, and it is recommended that it is best to install it with the original mirror image, not ghost, but ghost xp is also very It's mature, but it doesn't hurt to use it.