Export packaging standards by HS code

Engine disassembly: operation steps and Export packaging standards by HS codemaintenance suggestions The engine is the core part of the car, connecting all parts of the whole vehicle. The disassembly and installation of the engine is one of the most basic and important parts of the car maintenance.The following are the operating steps and maintenance suggestions for engine disassembly: Step 1: Preparation work Before starting engine disassembly, you need to arrange professional maintenance tools and necessary equipment, such as electric lifters, wrenches, pliers, riveting guns, clutch removers, cylinder bottom disassemblers, silencer disassemblers, suspension Frame adjuster, etc., and it is also important to ensure that the site is bright, clean and tidy. Step 2: Disassembly of the exhaust system The discharge system is the discharge channel of the exhaust gas generated by the engine during operation, including the exhaust pipe, silencer, exhaust gas recoverer and other parts. Disassembling the discharge system requires certain skills and techniques. It is necessary to pay attention to protect the cleanliness of the site and cut off the power supply to ensure safety. Step 3: Disassembly of the cooling system The cooling system is a part of the component used for engine heat dissipation. The cooling system includes radiators, pumps, coolant pipelines, etc.When disassembling the cooling system, use the radiator remover carefully. Remember to open the coolant on the cooling system to release steam first and loosen the fastening screw. Try to avoid the coolant leaking to the thermal machine, because it will lead to corrosion and other problems of the thermal machine. Step 4: Disassembly of the fuel system The fuel system is a component that supplies fuel to the engine. The fuel system includes fuel tank, oil pump, fuel injector, etc. When disassembling the fuel system, you need to be careful not to let the fuel leak to the vehicle, which will cause safety hazards. When disassembling the fuel injector, there are often problems such as nozzle blockage, oil leakage, increased resistance, etc. It is recommended to repair it before replacing it to ensure the safety, hygiene and good operation of the fuel system. Step 5: External disconnection There are many connections with external components on the engine, including transmission systems, manual transmissions, etc.During the disassembly process, remember to put down the transmission system first in order to remove the manual transmission and other related connections. Step 6: Disassembly of the engine head assembly. This step requires removing the cylinder head, valve rod, valve spring, valve and other parts, and then remove the cylinder head bolt before removing its cover. Then, take out the inner pad, upper pad, valve rod and valve of the valve spring, and pay attention to release them on the sheet in order of composition. After disassembly, please clean and overhaul the valve and valve rod to ensure that the parts are clean and free of corrosion during the maintenance process. At the same time, carefully grasp the position of the vacuum pump, the oil seal in front of the crankshaft, the mountain cover, etc. to ensure that they work normally after reinstallation. Step 7: Remove the piston assembly, separate the engine cylinder and the connecting rod, disconnect the oil pump and the crankshaft sprocket connection, and then remove the piston, to the connecting rodThe bottom is checked and repaired. After reinstalling, use the ring clip to ensure the normal cooperation and safety of the connecting rod and the piston. Step 8: Remove the crankshaft assembly to separate the crankshaft from the crankshaft sprocket, and then check the breakable connecting rod hole part of the pad to further determine the safety of the crankshaft. Step 9: Overhaul and reassemble. During the disassembly process, quality-assured parts and accessories can ensure technically feasible disassembly and reorganization. It is recommended to verify the operation process many times. At the same time, maintain professional instruments and equipment, carry out on-site maintenance and overhaul with the method that best meets the actual situation, and for each Each step, every part and every part are strictly inspected and tested to ensure safety and efficiency. On this basis, a perfect engine is assembled with confidence, and comprehensive functional tests are carried out to ensure that the original performance can be maintained after the repair is completed.In short, the disassembly of the engine requires patience and meticulousness, and the operation process needs to be cautious, because any omission or negligence may affect the overall stability and efficiency of the vehicle. It is recommended that you seek professional help when carrying out such repairs to ensure the safety of you and your car.

Contact Us
Phone：020-83484653