1. The engine valve uses the cylinder-by-cylinder adjustment method. The following are the specific methods:Adjust a cylinder: When a cylinder is at the stop point of compression (the way to determine the stop point is to open the key and turn the flywheel to see a cylinder high-pressure line jump and then turn the flywheel slightly.
2. Assemble the cylinder head. After the valve oil seal on the 465 cylinder head, camshaft, rocker arm and rocker arm is assembled, the valve gap can be adjusted. How to use a wrench? Loosen the valve adjustment nut with a 12-14 wrench, loosen or tighten the internal screw with one word, and then insert the plug ruler into the gap to pull out the gap you need. Adjust the formula.
3. There is a plastic cover at the gearbox position, pry open the rear crankshaft, and align the T-mark on the flywheel and the sign on the gearbox hole. Then there are four rocker arms to move. Adjust these four first, then turn around, and adjust the other four. It is best to adjust the cold car, otherwise it is not easy to start. Non-professionals should find Repair shop adjustment.
4. First, check the marks, adjust the intake valve of the 4-cylinder, adjust the exhaust valve of the 4-cylinder, turn the crankshaft, and then adjust the remaining valves.
1. Hello,Is the oil pump working? Please take a look and listen to the sound. If there is a sound in the oil pump, you can unplug the oil pipe of the fuel injector oil track to see if there is oil. If there is oil, check the line.
2. If the oil pump doesn't work, the fuel injector will certainly not inject oil. The oil pump is the source of pressure. Without pressure, it is normal for the fuel injector not to spray. The oil pump is broken. Go to 4S or the repair shop outside to replace it.
3. The engine fuel injector does not inject fuel due to the blockage of the fuel injector or insufficient fuel supply. The fuel injector is blocked: The nozzle on the fuel injector may be blocked due to the accumulation of sediment, dirt or oil stains, resulting in the inability to inject fuel normally.
4. The spray hole is blocked. You can use a needle to dredge it. After dredging, it should be carefully cleaned. The large plane of the needle valve body has poor contact with the main plane of the fuel injector, or the cylindrical surface of the needle valve is worn out.
5. When the fuel injecte fails, it will lead to increased carbon accumulation in the engine, unstable idle speed, increased fuel consumption, weak acceleration, difficult start-up, emission exceeding the standard, etc. If it is serious, it will cause the fuel injector to be blocked, which will damage the engine. The fuel injector is a simple solenoid valve.
6. Iveco's fuel injector does not inject fuel, and there is no electricity. Check whether there is any abnormal sound, and learn to distinguish the abnormal sound that belongs to the reasonable sound. It is difficult for ordinary car owners to distinguish which are faulty abnormal noise and which are reasonable abnormal noise. When I went to the repair shop to test the abnormal sound of the vehicles, only nearly 20% of the vehicles really had problems.
1. Hello! The 465 engine is the most commonly used.The engine series with the largest output was introduced in the early 1990s, with the production code 465, which is also the most stable engine.
2. "New Tianlong" adheres to the consistent excellent quality of Dongfeng commercial vehicles. After 5 years of technical improvement and optimization and upgrading, it was grandly launched in November 2011! While inheriting the advantages of traditional technology, Dongfeng Xintianlong constantly pursues innovation to meet the needs of users in the new era, constantly leads the development of the industry and becomes a value benchmark.
3. Japan's f8b technology has been used for nearly 20 years in China. The technology is mature, it is produced nationwide, the price is relatively cheap, and it is still relatively fuel-saving. The most important thing is that the maintenance cost is low. It would be better if it was electric injection.
Chang'an Star 2nd generation, there is a 16V logo on the body wing plate, indicating that the engine of this car uses 16 valves. The engine model is 474 displacement 13L, 4 cylinders, 4 valves per cylinder, a total of 1 6 valves, that is, 16V.
Chang'an Star 2 can be replaced, 5w~30 model oil.
The following are the basic parameter configurations of Chang'an Star 2 van: engine: 2L, 4L naturally aspirated engine or 2L turbocharged engine. Transmission: 5-speed manual transmission. Length, width and height: 3985mm×1635mm×1920mm. Wheelbase: 2600mm. Vehicle weight: 1040-1080kg.
1, "The relevant content introduction is as follows: the intake valve of the 465 engine is 20, and the exhaust valve is 25: when the engine is working, the valve will rise due to the temperature High and inflated.
2. Hello, the intake valve is 0.35mm and the exhaust valve is 0.45mm. I wish you a happy car.
3. The gap between the engine intake valve is 0.20mm, and the exhaust valve is 0.25mm.
4. Standard data of intake valve gap: 0.03mm; standard data of exhaust valve gap: 0.05mm. Nowadays, the valve of the car engine generally does not need to be adjusted, and is equipped with a self-adjusting device. As long as it runs for a few minutes, the valve gap will be automatically eliminated.
HS code-driven portfolio diversification-APP, download it now, new users will receive a novice gift pack.
1. The engine valve uses the cylinder-by-cylinder adjustment method. The following are the specific methods:Adjust a cylinder: When a cylinder is at the stop point of compression (the way to determine the stop point is to open the key and turn the flywheel to see a cylinder high-pressure line jump and then turn the flywheel slightly.
2. Assemble the cylinder head. After the valve oil seal on the 465 cylinder head, camshaft, rocker arm and rocker arm is assembled, the valve gap can be adjusted. How to use a wrench? Loosen the valve adjustment nut with a 12-14 wrench, loosen or tighten the internal screw with one word, and then insert the plug ruler into the gap to pull out the gap you need. Adjust the formula.
3. There is a plastic cover at the gearbox position, pry open the rear crankshaft, and align the T-mark on the flywheel and the sign on the gearbox hole. Then there are four rocker arms to move. Adjust these four first, then turn around, and adjust the other four. It is best to adjust the cold car, otherwise it is not easy to start. Non-professionals should find Repair shop adjustment.
4. First, check the marks, adjust the intake valve of the 4-cylinder, adjust the exhaust valve of the 4-cylinder, turn the crankshaft, and then adjust the remaining valves.
1. Hello,Is the oil pump working? Please take a look and listen to the sound. If there is a sound in the oil pump, you can unplug the oil pipe of the fuel injector oil track to see if there is oil. If there is oil, check the line.
2. If the oil pump doesn't work, the fuel injector will certainly not inject oil. The oil pump is the source of pressure. Without pressure, it is normal for the fuel injector not to spray. The oil pump is broken. Go to 4S or the repair shop outside to replace it.
3. The engine fuel injector does not inject fuel due to the blockage of the fuel injector or insufficient fuel supply. The fuel injector is blocked: The nozzle on the fuel injector may be blocked due to the accumulation of sediment, dirt or oil stains, resulting in the inability to inject fuel normally.
4. The spray hole is blocked. You can use a needle to dredge it. After dredging, it should be carefully cleaned. The large plane of the needle valve body has poor contact with the main plane of the fuel injector, or the cylindrical surface of the needle valve is worn out.
5. When the fuel injecte fails, it will lead to increased carbon accumulation in the engine, unstable idle speed, increased fuel consumption, weak acceleration, difficult start-up, emission exceeding the standard, etc. If it is serious, it will cause the fuel injector to be blocked, which will damage the engine. The fuel injector is a simple solenoid valve.
6. Iveco's fuel injector does not inject fuel, and there is no electricity. Check whether there is any abnormal sound, and learn to distinguish the abnormal sound that belongs to the reasonable sound. It is difficult for ordinary car owners to distinguish which are faulty abnormal noise and which are reasonable abnormal noise. When I went to the repair shop to test the abnormal sound of the vehicles, only nearly 20% of the vehicles really had problems.
1. Hello! The 465 engine is the most commonly used.The engine series with the largest output was introduced in the early 1990s, with the production code 465, which is also the most stable engine.
2. "New Tianlong" adheres to the consistent excellent quality of Dongfeng commercial vehicles. After 5 years of technical improvement and optimization and upgrading, it was grandly launched in November 2011! While inheriting the advantages of traditional technology, Dongfeng Xintianlong constantly pursues innovation to meet the needs of users in the new era, constantly leads the development of the industry and becomes a value benchmark.
3. Japan's f8b technology has been used for nearly 20 years in China. The technology is mature, it is produced nationwide, the price is relatively cheap, and it is still relatively fuel-saving. The most important thing is that the maintenance cost is low. It would be better if it was electric injection.
Chang'an Star 2nd generation, there is a 16V logo on the body wing plate, indicating that the engine of this car uses 16 valves. The engine model is 474 displacement 13L, 4 cylinders, 4 valves per cylinder, a total of 1 6 valves, that is, 16V.
Chang'an Star 2 can be replaced, 5w~30 model oil.
The following are the basic parameter configurations of Chang'an Star 2 van: engine: 2L, 4L naturally aspirated engine or 2L turbocharged engine. Transmission: 5-speed manual transmission. Length, width and height: 3985mm×1635mm×1920mm. Wheelbase: 2600mm. Vehicle weight: 1040-1080kg.
1, "The relevant content introduction is as follows: the intake valve of the 465 engine is 20, and the exhaust valve is 25: when the engine is working, the valve will rise due to the temperature High and inflated.
2. Hello, the intake valve is 0.35mm and the exhaust valve is 0.45mm. I wish you a happy car.
3. The gap between the engine intake valve is 0.20mm, and the exhaust valve is 0.25mm.
4. Standard data of intake valve gap: 0.03mm; standard data of exhaust valve gap: 0.05mm. Nowadays, the valve of the car engine generally does not need to be adjusted, and is equipped with a self-adjusting device. As long as it runs for a few minutes, the valve gap will be automatically eliminated.
Agricultural machinery HS code lookups
author: 2024-12-23 22:35Organic chemicals (HS code ) patterns
author: 2024-12-23 21:47International trade compliance dictionary
author: 2024-12-23 21:37Supplier compliance audit automation
author: 2024-12-23 20:49Plant-based proteins HS code verification
author: 2024-12-23 20:11Deriving product origin via HS code
author: 2024-12-23 22:36Advanced materials HS code classification
author: 2024-12-23 22:30HS code mapping for re-importation
author: 2024-12-23 22:11Advanced export forecasting models
author: 2024-12-23 21:38931.68MB
Check311.82MB
Check268.11MB
Check924.95MB
Check517.71MB
Check726.53MB
Check216.24MB
Check492.74MB
Check693.65MB
Check359.83MB
Check523.69MB
Check422.67MB
Check331.29MB
Check458.93MB
Check838.94MB
Check138.15MB
Check264.87MB
Check726.96MB
Check838.54MB
Check692.78MB
Check762.23MB
Check918.21MB
Check265.94MB
Check979.44MB
Check982.84MB
Check364.46MB
Check575.45MB
Check994.92MB
Check766.46MB
Check292.65MB
Check531.14MB
Check915.72MB
Check936.71MB
Check979.31MB
Check275.16MB
Check352.29MB
CheckScan to install
HS code-driven portfolio diversification to discover more
Netizen comments More
230 Pharma supply chain mapping by HS code
2024-12-23 21:32 recommend
2162 Customizable export data queries
2024-12-23 21:24 recommend
1910 global trade intelligence
2024-12-23 21:17 recommend
896 Free global trade data sources
2024-12-23 21:02 recommend
2246 Global trade reporting frameworks
2024-12-23 20:06 recommend