HS code-based value chain optimization

List of the catalogue of this article:

• 1,HS code-based value chain optimization How should car glass be replaced? Introduction to car glass replacement
• 2, How is car glass made
• 3, How to maintain the windshield of the car?
• 4, How to maintain Car glass
• 5, car glass should How to change
• 6, Correct maintenance method of car glass

How should car glass be replaced?Introduction to car glass replacement

Replace triangle glass. Some triangular window glass is glued together with glass glue like a windshield, and some are fixed with screws and screws. This kind of vehicle first needs to find the screw and the screw position, most of which can be seen under the seal, and the bolts are installed under the interior panel.

In fact, it is very easy to replace the door glass. The main task is to remove the door interior panel, and pay special attention not to damage the door interior panel. The specific practice is as follows. First, find and remove the hidden bolts; remove the latch and boldly remove the door interior panel; adjust the window, remove the glass fixing bolt, and take out the glass.

Replace in the car 4S store; it can be replaced in the place where car glass is sold; some auto repair shops have cooperative car glass replacement stores. Many domestic manufacturers use Fuyao glass, and of course there are also other brands, such as Saint-Gobain, Xinyi, etc.

When replacing the car glass, you must first disconnect the cable from the negative pole and terminal of the battery, and then remove the hidden bolts, the lock and the decorative panel inside the door. Adjust the window and remove the glass fixing bolt to take out the glass. After this step is completed, the process of replacing the car glass can begin.

First, remove the water stop strip around the original windshield, and then remove the original windshield. Finally, clean up the original base layer and install a new windshield, and then install the original water stop strip. The overall process takes about an hour.

If you want to replace the windshield of the car by yourself, we need the following materials: a knife, a Phillips screwdriver, pliers, transparent tape and glue.

How is automotive glass made

1. The production of automotive glass is to heat the glass in the heating furnace to a temperature close to softening temperature, and then quickly send the glass into the wind grille of different cooling intensities. The cooling is uneven, causing the glass main viewing area and the surrounding area to generate different stress. Generally speaking, this kind of glass is regional tempered glass.

2. The production of automotive glass is to heat the glass to a near softening temperature in the heating furnace, and thenThe glass is quickly sent into the wind grid of different cooling intensities, and the glass is unevenly cooled, causing different stresses in the main view area of the glass and the surrounding area. Generally, the glass produced in this kind is regional tempered glass.

3. The front glass of the car is made of glass and is composed of two layers of glass.

4. The front windshield of the car is reprocessed from ordinary flat glass: the front gear of the passenger car adopts a laminated glass composed of two pieces of glass, and the front gear of the truck/agricultural vehicle is a single piece of tempered glass.

How to maintain the windshield of the car?

1. Use a special or suitable wiper, and replace it in time (generally once a year) to prevent scratching the front gear glass; keep the front gear clean often. If there is debris stuck, try not to use a wiper to solve it. It should be carefully removed with a towel or other tools as much as possible.Use glass water for cars.

2. Apply suitable wiper products and replace them immediately: For wiper blads, they are responsible for cleaning the front windshield of the car. If incorrect wiper flaves or brittle wipers are applied, they will not only not be able to clean the laminated glass, but will also continue to destroy the laminated glass.

3. Reasonable use of glass water. In daily glass maintenance, we should choose glass water reasonably according to different seasons and weather. When we find that the windshield of the car becomes blurred, it will be much clearer to clean it with appropriate glass water. If you find that there is a problem with the glass reflection when driving at night, you can also use glass water to wipe it.

4. Reasonable use of glass water: In life, car owners can make reasonable use of glass water to solve the problem.The problem of windshield blurring in driving, and in the usual glass maintenance process, we should choose the appropriate glass water according to the specific situation of the season and weather, so that the cleaning will be much brighter.

How to maintain car glass

Use qualified glass water. In the process of glass maintenance, appropriate glass water should be selected according to the specific conditions of the season and weather.

Glass maintenance and repair that Xiang Ai Car should pay attention to. Thoroughly removing the dirt from the car glass is the first step in maintaining the car glass. It is a good choice to choose detergents and related cleaning products carefully. It needs to be turned off after turning on the defogging and heating for 5-10 minutes, otherwise it is easy to cause the rear windshield to burst.

In the usual glassDuring the maintenance process, we should choose the appropriate glass water according to the specific conditions of the season and weather. When we find that the surface of the windshield is blurred, it will be much brighter to clean it with appropriate glass water. If you find the problem of glass reflection at night, you can also wipe it with glass water.

Hello, 1 Use a special or suitable wiper blade and replace it in time (usually once a year) to avoid scratching the front glass. 2 Always adhere to the hygiene of the front gear. If there are sticky debris, try not to use a wiper to deal with it. You should use a towel or other things to remove it as much as possible. 3 Use glass water for cars.

In the usual glass maintenance process, it is necessary to choose the appropriate glass water according to the specific conditions of the season and weather. When we find that the surface of the windshield is blurred, it will be much brighter if cleaned with appropriate glass water.If you find the problem of glass reflection at night, you can also wipe it with glass water.

How to change the car glass

1. Replace the triangular glass. Some triangular window glass is glued together with glass glue like a windshield, and some are fixed with screws and screws. This kind of vehicle first needs to find the screw and the screw position, most of which can be seen under the seal, and the bolts are installed under the interior panel.

2. The door glass is actually very easy to replace. The main work is to remove the door interior panel. Pay special attention not to damage the door interior panel. The specific practice is as follows. First, find and remove the hidden bolts; remove the latch and boldly remove the door interior panel; adjust the window, remove the glass fixing bolt, and take out the glass.

3. Replace it in the car 4S store; it can be replaced in the place where car glass is sold; some auto repair shops have cooperative car glass replacement stores. Many domestic manufacturers use Fuyao glass, and of course there are also other brands, such as Saint-Gobain, Xinyi, etc.

4. When replacing the car glass, first disconnect the cable from the negative pole and terminal of the battery, and then remove the hidden bolts, the lock and the decorative panel inside the door. Adjust the window and remove the glass fixing bolt to take out the glass. After this step is completed, the process of replacing the car glass can begin.

5. If you want to replace the windshield of the car by yourself, we need the following materials: a knife, a Phillips screwdriver, pliers, transparent tape and glue.

6. First, prepare the art knife, one-word screwdriver and other utensils, in addition, equipped with a silicone gun and a silicone, first take out the original sealed water stop strip, then take out the original windshield, remove the original glue material, re-ply a new silicone, then put on the new windshield, and finally reinstall the original sealed water stop strip.

Correct maintenance method of car glass

1. Thoroughly removing the dirt of car glass is the first step to maintain car glass. It is a good choice to choose detergents and related cleaning products carefully. It needs to be turned off after turning on the defogging and heating for 5-10 minutes, otherwise it is easy to cause the rear windshield to burst. Within two days of changing the glass, do not wash the car and try to drive on the flat road.

2. Use qualified glass water. In the process of glass maintenance, appropriate glass water should be selected according to the specific conditions of the season and weather.

3. Hello, 1 Use a special or suitable wiper, and replace it in time (usually once a year) to avoid scratching the front glass. 2 Always adhere to the hygiene of the front gear. If there are sticky debris, try not to use a wiper to deal with it. You should use a towel or other things to remove it as much as possible. 3 Use glass water for cars.

4. In the usual glass maintenance process, we should choose the appropriate glass water according to the specific conditions of the season and weather. When we find that the surface of the windshield is blurred, it will be much brighter to clean it with appropriate glass water. If you find the problem of glass reflection at night, you can also wipe it with glass water.